@article { author = {khameneh asl, shahab and golzarian, reza and salahimehr, behnam and fardi, ali}, title = {Effect of Process Parameters on Microstructure and Efficiency of Tubular Alumina Catalyst Prepared by Doped Anodizing Method with Platinum Particles}, journal = {Space Science, Technology and Applications}, volume = {2}, number = {1}, pages = {109-117}, year = {2022}, publisher = {Iranian Space Research Institute}, issn = {2783-4557}, eissn = {2783-4557}, doi = {10.22034/jssta.2022.327760.1065}, abstract = {The use of thermal knives as holding mechanism and non-explosive release in the field of space mechanisms has always been considered. In these mechanisms, the use of materials with high melting points and low weight, as well as the possibility of production on a small scale is a major challenge. Therefore, the use of platinum / alumina catalysts can be a good solution to the leading problems in this field.The purpose of this paper is to prepare a high specific surface alumina base using the process of anodizing aluminum and coating it with platinum particles. Thus, the present study consists of two stages; In the first stage, aluminum is anodized in oxalic acid solution and its parameters are optimized in order to achieve aluminum nanotubes with various diameters and wall thicknesses, as well as the applied voltage, electrolyte concentration and anodizing conditions. In the next step, platinum nanoparticles were precipitated in different amounts using metal salt and suitable solvent using electrochemical method. The results showed that the obtained nanowires have a diameter of about 200 nm and a length of several micrometers. All samples were mechanically polished and it was shown that the aluminum anode oxide membranes were completely filled with a combination of metals. Also, the performed analyzes showed that the obtained nanowires are stable inside the membrane}, keywords = {Anodizing# Alumina# Alatinuim# Thermal knife# Thermal element# Catalyst}, title_fa = {اثر پارامترهای فرایندی بر ریزساختار و بازدهی کاتالیست آلومینای لوله‌ای تهیه شده به روش اندایزینگ دوپ شده با ذرات پلاتین}, abstract_fa = {استفاده از چاقوی حرارتی به عنوان یکی از مکانیزم‌های نگهدارنده و رهایش غیرانفجاری در حوزه مکانیزم‌های فضایی همواره مورد توجه بوده است. در این مکانیزم‌ها، استفاده از مواد با نقطه ذوب بالا و وزن پایین و درعین‌حال امکان تولید در مقیاس‌های کوچک یک چالش اساسی محسوب می‌شود. از این‌رو، استفاده از کاتالیست‌های پلاتین/ آلومینا می‌توانند راه‌گشای مناسبی برای مشکلات پیش‌رو در این زمینه باشند. هدف از این مقاله، تهیه زیرپایه آلومینایی با سطح ویژه بالا با استفاده از فرایند آندایزینگ آلومینیوم و پوشش‌دهی آن با ذرات پلاتین است. بدین‌ترتیب، پژوهش حاضر شامل دو مرحله است؛ در مرحله اوّل، آندایزینگ آلومینیوم در محلول اسید اگزالیک انجام شده و بهینه‌سازی پارامترهای آن به منظور رسیدن به نانولوله‌های آلومینایی با قطر و ضخامت دیواره متنوع صورت پذیرفته و نیز بهینه‌سازی ولتاژ اعمالی، غلظت الکترولیت و شرایط آندایزینگ انجام‌ شده است. بررسی در این مرحله با استفاده از میکروسکوپ الکترونی روبشی انجام شده و داده‌های مربوط به سطح ویژه استخراج شده است. در مرحله بعدی، نانوذرات پلاتین در مقادیر مختلف با استفاده از نمک فلزی و حلال مناسب با استفاده از روش الکتروشیمی رسوب‌گذاری شده است. نتایج به‌دست آمده نشان داد که نانوسیم‌های به‌دست‌ آمده دارای قطر حدود 200 نانومتر و طول چند میکرومتر هستند. تمام نمونه‌ها پولیش مکانیکی شده و نشان داده‌ شد که غشاهای اکسید آندی آلومینیوم به‌طور کامل با ترکیب فلزات پرشده است. هم‌چنین، آنالیزهای انجام ‌شده نشان داد که نانوسیم‌های به‌دست‌ آمده در داخل غشاء ماندگار هستند}, keywords_fa = {آندایزینگ# آلومینا# پلاتین# چاقوی حرارتی# المان حرارتی# کاتالیست}, url = {https://journal.isrc.ac.ir/article_149825.html}, eprint = {https://journal.isrc.ac.ir/article_149825_9bac5a49838e6b9760f17993685ff110.pdf} }